View MCR22-6_674844.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

MCR22-6, MCR22-8
Preferred Device
Sensitive Gate Silicon Controlled Rectifiers
Reverse Blocking Thyristors
Designed and tested for repetitive peak operation required for CD ignition, fuel ignitors, flash circuits, motor controls and low-power switching applications. * 150 Amperes for 2 s Safe Area * High dv/dt * Very Low Forward "On" Voltage at High Current * Low-Cost TO-226AA (TO-92) * Device Marking: Device Type, e.g., MCR22-6, Date Code
MAXIMUM RATINGS (TJ = 25C unless otherwise noted)
Rating Peak Repetitive Off-State Voltage (RGK = IK, TJ = to +110C, Sine Wave, 50 to 60 Hz, Gate Open) MCR22-6 MCR22-8 Symbol VDRM, VRRM 400 600 IT(RMS) ITSM 1.5 15 Amps Amps 1 Value Unit Volts
http://onsemi.com
SCRs 1.5 AMPERES RMS 400 thru 600 VOLTS
G A K
*40
On-State Current RMS (180 Conduction Angles, TC = 80C) Peak Non-repetitive Surge Current, TA = 25C (1/2 Cycle, Sine Wave, 60 Hz) Circuit Fusing Considerations (t = 8.3 ms) Forward Peak Gate Power (Pulse Width 1.0 msec, TA = 25C) Forward Average Gate Power (t = 8.3 msec, TA = 25C) Forward Peak Gate Current (Pulse Width 1.0 s, TA = 25C) Reverse Peak Gate Voltage (Pulse Width 1.0 s, TA = 25C) Operating Junction Temperature Range @ Rated VRRM and VDRM Storage Temperature Range
2
3
I2t PGM PG(AV) IFGM VRGM TJ Tstg
0.9 0.5 0.1 0.2 5.0 -40 to +110 -40 to +150
A2s Watt Watt 1 Amp Volts C C 2 3
TO-92 (TO-226AA) CASE 029 STYLE 10
PIN ASSIGNMENT
Cathode Gate Anode
ORDERING INFORMATION
See detailed ordering and shipping information in the package dimensions section on page 7 of this data sheet. Preferred devices are recommended choices for future use and best overall value.
(1) VDRM and VRRM for all types can be applied on a continuous basis. Ratings apply for zero or negative gate voltage; however, positive gate voltage shall not be applied concurrent with negative potential on the anode. Blocking voltages shall not be tested with a constant current source such that the voltage ratings of the devices are exceeded.
(c) Semiconductor Components Industries, LLC, 2000
1
May, 2000 - Rev. 3
Publication Order Number: MCR22-6/D
MCR22-6, MCR22-8
THERMAL CHARACTERISTICS
Characteristic Thermal Resistance, Junction to Case Thermal Resistance, Junction to Ambient Lead Solder Temperature (Lead Length 1/16 from case, 10 s Max) Symbol RJC RJA TL Max 50 160 +260 Unit C/W C/W C
q
ELECTRICAL CHARACTERISTICS (TC = 25C unless otherwise noted.)
Characteristic Symbol Min Typ Max Unit
OFF CHARACTERISTICS
Peak Repetitive Forward or Reverse Blocking Current (VAK = Rated VDRM or VRRM; RGK = 1000 Ohms) IDRM, IRRM TC = 25C TC = 110C -- -- -- -- 10 200 A A
ON CHARACTERISTICS
Peak Forward On-State Voltage(1) (ITM = 1 A Peak) Gate Trigger Current (Continuous dc)(2) (VAK = 6 Vdc, RL = 100 Ohms) Gate Trigger Voltage (Continuous dc)(2) (VAK = 7 Vdc, RL = 100 Ohms) Gate Non-Trigger Voltage(1) (VAK = 12 Vdc, RL = 100 Ohms) Holding Current (VAK = 12 Vdc, Gate Open) Initiating Current = 200 mA TC = 25C TC = -40C TC = 25C TC = -40C TC = 110C IH TC = 25C TC = -40C -- -- 2.0 -- 5.0 10 mA VTM IGT VGT VGD -- -- -- -- -- 0.1 1.2 30 -- -- -- -- 1.7 200 500 0.8 1.2 -- Volts A Volts Volts
DYNAMIC CHARACTERISTICS
Critical Rate of Rise of Off-State Voltage (TC = 110C) dv/dt -- 25 -- V/s
(1) Pulse Width = 1.0 ms, Duty Cycle (2) RGK Current not included in measurement.
v1%.
http://onsemi.com
2
MCR22-6, MCR22-8
Voltage Current Characteristic of SCR
+ Current Anode + VTM on state IRRM at VRRM IH
Symbol
VDRM IDRM VRRM IRRM VTM IH
Parameter
Peak Repetitive Off State Forward Voltage Peak Forward Blocking Current Peak Repetitive Off State Reverse Voltage Peak Reverse Blocking Current Peak on State Voltage Holding Current Reverse Blocking Region (off state) Reverse Avalanche Region Anode -
+ Voltage IDRM at VDRM Forward Blocking Region (off state)
CURRENT DERATING
TA , MAXIMUM ALLOWABLE AMBIENT TEMPERATURE ( C) TC , MAXIMUM ALLOWABLE CASE TEMPERATURE ( C)
140
140 120 100 80 60 40 20 0 0 dc = 180 = CONDUCTION ANGLE 0.2 0.4 0.6 0.8 1.0 IT(AV), AVERAGE ON-STATE CURRENT (AMP)
100 = 180 = CONDUCTION ANGLE dc
60
20 0 0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0 IT(AV), AVERAGE ON-STATE CURRENT (AMPS)
Figure 1. Maximum Case Temperature
Figure 2. Maximum Ambient Temperature
http://onsemi.com
3
MCR22-6, MCR22-8
5.0
3.0 2.0 TJ = 110C 25C 1.0 I T , INSTANTANEOUS ON-STATE CURRENT (AMP) 0.7 0.5
0.3 0.2
0.1 0.07 0.05
0.03 0.02
0.01 0 0.5 1.0 1.5 2.0 2.5 VT, INSTANTANEOUS ON-STATE VOLTAGE (VOLTS)
Figure 3. Typical Forward Voltage
r(t), TRANSIENT THERMAL RESISTANCE (NORMALIZED)
1.0 0.7 0.5 0.3 0.2 0.1 0.07 0.05 0.03 0.02 0.01 0.1
0.2
0.5
1.0
2.0
5.0
10
20
50 t, TIME (ms)
100
200
500
1000
2000
5000
10000
Figure 4. Thermal Response
http://onsemi.com
4
MCR22-6, MCR22-8
TYPICAL CHARACTERISTICS
0.8 VGT, GATE TRIGGER VOLTAGE (VOLTS) I GT GATE TRIGGER CURRENT ( A) 100 110 VAK = 7.0 V RL = 100
100 50 30 20 10 5.0 3.0 2.0 1.0 -40
0.7
0.6
0.5
0.4 0.3 -75
-50
-25
0
25
50
75
-20
0
20
40
60
80
100 110
TJ, JUNCTION TEMPERATURE (C)
TJ JUNCTION TEMPERATURE (C)
Figure 5. Typical Gate Trigger Voltage
Figure 6. Typical Gate Trigger Current
10 I H , HOLDING CURRENT (mA)
P(AV) MAXIMUM AVERAGE POWER DISSIPATION (WATTS)
2.0 1.8 1.6 1.4 1.2 1.0 0.8 0.6 0.4 dc 30 60 90 120 180
VAK = 12 V RL = 100 5.0
2.0
0.2 0 0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 IT(AV), AVERAGE ON-STATE CURRENT (AMPS)
1.0 -40
-20
0
20
40
60
80
100 110
TJ, JUNCTION TEMPERATURE (C)
Figure 7. Typical Holding Current
Figure 8. Power Dissipation
http://onsemi.com
5
MCR22-6, MCR22-8 TO-92 EIA RADIAL TAPE IN FAN FOLD BOX OR ON REEL
H2A H2A H2B H2B
H W2 H4 H5 L1 L F1 F2 P2 P1 P P2 D H1 W1 W T T2 T1
Figure 9. Device Positioning on Tape
Specification Inches Symbol
D D2 F1, F2 H H1 H2A H2B H4 H5 L L1 P P1 P2 T T1 T2 W W1 W2
Millimeter Max Min
3.8 0.38 2.4 1.5 8.5 0 0 18 15.5 8.5 2.5 12.5 5.95 3.55 0.15 -- 0.35 17.5 5.5 .15
Item Tape Feedhole Diameter Component Lead Thickness Dimension Component Lead Pitch Bottom of Component to Seating Plane Feedhole Location Deflection Left or Right Deflection Front or Rear Feedhole to Bottom of Component Feedhole to Seating Plane Defective Unit Clipped Dimension Lead Wire Enclosure Feedhole Pitch Feedhole Center to Center Lead First Lead Spacing Dimension Adhesive Tape Thickness Overall Taped Package Thickness Carrier Strip Thickness Carrier Strip Width Adhesive Tape Width Adhesive Tape Position
Min
0.1496 0.015 0.0945 .059 0.3346 0 0 0.7086 0.610 0.3346 0.09842 0.4921 0.2342 0.1397 0.06 -- 0.014 0.6889 0.2165 .0059
Max
4.2 0.51 2.8 4.0 9.5 1.0 1.0 19.5 16.5 11 -- 12.9 6.75 3.95 0.20 1.44 0.65 19 6.3 0.5
0.1653 0.020 0.110 .156 0.3741 0.039 0.051 0.768 0.649 0.433 -- 0.5079 0.2658 0.1556 0.08 0.0567 0.027 0.7481 0.2841 0.01968
NOTES: 1. Maximum alignment deviation between leads not to be greater than 0.2 mm. 2. Defective components shall be clipped from the carrier tape such that the remaining protrusion (L) does not exceed a maximum of 11 mm. 3. Component lead to tape adhesion must meet the pull test requirements. 4. Maximum non-cumulative variation between tape feed holes shall not exceed 1 mm in 20 pitches. 5. Holddown tape not to extend beyond the edge(s) of carrier tape and there shall be no exposure of adhesive. 6. No more than 1 consecutive missing component is permitted. 7. A tape trailer and leader, having at least three feed holes is required before the first and after the last component. 8. Splices will not interfere with the sprocket feed holes.
http://onsemi.com
6
MCR22-6, MCR22-8
ORDERING & SHIPPING INFORMATION: MCR22 Series packaging options, Device Suffix
U.S. MCR22-6,8 MCR22-6RLRA MCR22-6RLRP MCR22-8ZL1 Europe Equivalent MCR22-8RL1 Shipping Radial Tape and Reel (2K/Reel) Bulk in Box (5K/Box) Radial Tape and Reel (2K/Reel) Radial Tape and Fan Fold Box (2K/Box) Radial Tape and Fan Fold Box (2K/Box) Description of TO92 Tape Orientation Flat side of TO92 and adhesive tape visible N/A, Bulk Round side of TO92 and adhesive tape visible Round side of TO92 and adhesive tape visible Flat side of TO92 and adhesive tape visible
PACKAGE DIMENSIONS
TO-92 (TO-226AA) CASE 029-11 ISSUE AJ
A R P L
SEATING PLANE
B
NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. CONTOUR OF PACKAGE BEYOND DIMENSION R IS UNCONTROLLED. 4. LEAD DIMENSION IS UNCONTROLLED IN P AND BEYOND DIMENSION K MINIMUM. INCHES MIN MAX 0.175 0.205 0.170 0.210 0.125 0.165 0.016 0.021 0.045 0.055 0.095 0.105 0.015 0.020 0.500 --- 0.250 --- 0.080 0.105 --- 0.100 0.115 --- 0.135 --- MILLIMETERS MIN MAX 4.45 5.20 4.32 5.33 3.18 4.19 0.407 0.533 1.15 1.39 2.42 2.66 0.39 0.50 12.70 --- 6.35 --- 2.04 2.66 --- 2.54 2.93 --- 3.43 ---
K
XX G H V
1
D J C SECTION X-X N N
DIM A B C D G H J K L N P R V
STYLE 10: PIN 1. CATHODE 2. GATE 3. ANODE
http://onsemi.com
7
MCR22-6, MCR22-8
ON Semiconductor and are trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. "Typical" parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer.
PUBLICATION ORDERING INFORMATION
NORTH AMERICA Literature Fulfillment: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303-675-2175 or 800-344-3860 Toll Free USA/Canada Fax: 303-675-2176 or 800-344-3867 Toll Free USA/Canada Email: ONlit@hibbertco.com Fax Response Line: 303-675-2167 or 800-344-3810 Toll Free USA/Canada N. American Technical Support: 800-282-9855 Toll Free USA/Canada EUROPE: LDC for ON Semiconductor - European Support German Phone: (+1) 303-308-7140 (M-F 1:00pm to 5:00pm Munich Time) Email: ONlit-german@hibbertco.com French Phone: (+1) 303-308-7141 (M-F 1:00pm to 5:00pm Toulouse Time) Email: ONlit-french@hibbertco.com English Phone: (+1) 303-308-7142 (M-F 12:00pm to 5:00pm UK Time) Email: ONlit@hibbertco.com EUROPEAN TOLL-FREE ACCESS*: 00-800-4422-3781 *Available from Germany, France, Italy, England, Ireland CENTRAL/SOUTH AMERICA: Spanish Phone: 303-308-7143 (Mon-Fri 8:00am to 5:00pm MST) Email: ONlit-spanish@hibbertco.com ASIA/PACIFIC: LDC for ON Semiconductor - Asia Support Phone: 303-675-2121 (Tue-Fri 9:00am to 1:00pm, Hong Kong Time) Toll Free from Hong Kong & Singapore: 001-800-4422-3781 Email: ONlit-asia@hibbertco.com JAPAN: ON Semiconductor, Japan Customer Focus Center 4-32-1 Nishi-Gotanda, Shinagawa-ku, Tokyo, Japan 141-0031 Phone: 81-3-5740-2745 Email: r14525@onsemi.com ON Semiconductor Website: http://onsemi.com
For additional information, please contact your local Sales Representative.
http://onsemi.com
8
MCR22-6/D

▲Up To Search▲

Price & Availability of MCR22-6

	To Download MCR22-6 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .